Vaporesso iTank T Dual Mesh: a 6 ml clearomiser for DTL vaping

The Vaporesso iTank T Dual Mesh clearomiser is designed for vapers who prefer direct-to-lung (DTL) vaping and generous vapour production. Its 6 ml tank, 810 drip tip and wide-open airflow make it ideal for sub-ohm vaping.

This version of the iTank T is designed to work with Vaporesso’s GTi Dual Mesh coils. Two coil options are supplied with the clearomiser: 0.2 ohms for use between 60 and 75 W, and 0.4 ohms for a range between 50 and 60 W.

Adjustable top airflow and top-fill design

Vaporesso has positioned the airflow control at the top of the iTank T Dual Mesh. This top airflow allows you to adjust the airflow to your preference whilst minimising the risk of leaks associated with a bottom-mounted airflow.

Filling is also done from the top. Simply slide the top cap to access the filling port, then close it once the 6 ml capacity has been filled.

The 810 drip tip complements this design with an opening suited to DTL vaping.

GTi Dual Mesh 0.2 or 0.4 ohm: which coil should you choose?

The iTank T Dual Mesh comes with two coils to offer two power levels for direct-to-lung vaping.

GTi Dual Mesh 0.2 ohm

The GTi Dual Mesh 0.2 ohm coil operates between 60 and 75 W. It is designed for powerful DTL vaping and high vapour production.

• Draw type: DTL
• Power: 60 to 75 W
• Recommended PG/VG ratio: 30/70 to 20/80
• Recommended nicotine strength: up to 3 mg/ml

GTi Dual Mesh 0.4 ohm

The GTi Dual Mesh 0.4 ohm is still designed for DTL vaping, but operates at a lower power output of between 50 and 60 W.

• Draw type: DTL
• Power: 50 to 60 W
• Recommended PG/VG ratio: from 40/60 to 30/70
• Recommended nicotine strength: up to 6 mg/ml

GTi Dual Mesh coils use a dual mesh structure to increase the contact surface area with the cotton and ensure even heating.

Compatible with Vaporesso GTi coils

The iTank T Dual Mesh isn’t limited to the two coils supplied. It’s also compatible with Vaporesso’s standard GTi coils, allowing you to choose your coil based on the power and type of vapour you’re looking for.

When fitting a new coil, allow it to soak up e-liquid for around 10 minutes before using it for the first time. A loss of flavour or the appearance of a burnt taste usually indicates that the coil needs replacing.

A 24.5 mm diameter to build your setup

With a base diameter of 24.5 mm, the iTank T Dual Mesh can be paired with a mod suited to its dimensions and the power requirements of the GTi coils used.

Its stainless steel construction, 6 ml capacity and top airflow make it a clearomiser firmly geared towards sub-ohm DTL set-ups.

Find the Vaporesso iTank T Dual Mesh clearomiser in Switzerland at Sweetch.ch.

iTank T Dual Mesh specifications

• Brand: Vaporesso
• Model: iTank T Dual Mesh
• Type: sub-ohm clearomiser
• Inhalation type: DTL
• Capacity: 6 ml
• Alternative tank included: 3 ml
• Base diameter: 24.5 mm
• Material: stainless steel
• Airflow: top-mounted and adjustable
• Filling: top-fill with sliding top cap
• Drip tip: 810
• Coils included: GTi Dual Mesh 0.2 and 0.4 ohm
• Compatibility: Vaporesso GTi Dual Mesh and classic GTi coils

Contents of the box

• 1 iTank T Dual Mesh clearomiser with pre-installed 6 ml Pyrex glass tube
• 1 GTi Dual Mesh 0.2 ohm coil
• 1 GTi Dual Mesh 0.4 ohm coil
• 1 x 3 ml straight Pyrex tube
• 1 x spare fill port seal
• 2 x spare O-rings
• 1 x user manual